Start here: the routine in brief

Two failures spoil most readings: a reference edge mismatch (front setting, rear against the wall: a 40 mm error), and an invisible dot, washed out in sunlight at noon.

The routine that prevents both: set units and reference edge (check its icon), seat the tool at the starting point, aim at a surface the beam can return from, read without moving. Outdoors, steady the tool, and use the point finder camera or a target plate when the dot is invisible.

Before you start: what you need

  • A soft, damp cloth: to wipe dirt off. Never use aggressive cleaning agents or solvents (Leica and Bosch).
  • A dry, lint-free cloth for the optics: handle the reception lens the way you would glasses or a camera lens (Bosch. Leica says the same for its optical surfaces).
  • The case or pouch the tool came with.
  • Fresh batteries, or a charge: AAA or AA cells on some models, a built-in rechargeable battery on others. Bosch: all cells together, same manufacturer, same capacity.
  • A target plate, only where your maker describes one: Leica, for daylight measuring and poor reflection targets; Bosch, for reflective, porous or structured surfaces. White paper is Leica's own weak-signal substitute.
  • A known, fixed distance for the accuracy check: a room width or door opening of known exact length.

Measuring well, step by step

1. Set the units first. On Leica's D2 you press the plus and minus keys together to cycle through metres, feet, and feet and inches. On Bosch models you use the function button and the plus and minus buttons.

2. Set the reference edge, and read its icon. On Leica's D2 the rear is the standard setting. Hold the reference button for 2 seconds to set the front permanently. Bosch's GLM 400 offers three reference levels: the rear edge, for use against walls, the front edge, and the centre of the tripod thread. Bosch's GLM400CL goes back to the rear edge every time you switch it on. The GLM165-40 measures from the rear edge only. Where a Leica has a fold-out end piece for edges and corners, a sensor senses its position and adjusts the zero point, but only if you fold it fully to its locked position.

3. Seat the tool and aim. Put the reference edge against your starting point, aim, and press the measuring button briefly. Stay still until the value settles. On the GLM165-40 it typically appears within 0.5 seconds, and no later than 4 seconds (Bosch).

4. Choose a target the beam can return from. Leica warns that you can get errors when you measure to colourless liquids, glass, styrofoam or permeable surfaces, or at surfaces with a high gloss, and that dark surfaces take longer to measure. If your only target is glass, gloss or very dark, put a target plate or white paper on it and measure to that.

5. Use continuous measurement for min and max. On Leica's D2, hold ON/DIST for 2 seconds to measure continuously, with the smallest and largest values shown as min and max. For a maximum, such as a room diagonal, sweep slowly into the corner. For a minimum, the true horizontal distance, sweep past the point square to the target. On Bosch the same mode is real time measurement, and on the GLM165-40 it updates about every 0.5 seconds.

6. Add and subtract instead of writing offsets down. Both makers build addition and subtraction into the sequence, including adding areas and volumes on Leica models.

Area, volume and indirect measurements

Area. Pick the area function, then measure length and width one after the other (Bosch GLM165-40. Leica's D2 works the same way). Use the same reference edge for both readings.

Volume. Pick volume, then measure length, width and height in that order. Bosch keeps the laser on between the three measurements (GLM165-40). Do not change the reference setting in the middle of the sequence.

Indirect measurement (Pythagoras). This mode works out a distance you cannot shoot directly, such as a height from ground level, from two or three other measurements. Leica's 2-point sequence is to aim at the upper point and trigger, then aim at the lower point at right angles to the distance you want, keeping the instrument as horizontal as possible for the horizontal shot. Bosch's condition for the GLM165-40 is a right angle between the distance you want, the height, and the horizontal distance, the depth. Bosch also warns, in the GLM400CL instructions, that an indirect measurement is always less accurate than a direct one. Use a tripod for heights that need two or three shots, as Leica advises, because hand movement between shots is the biggest source of error in the calculation.

Stake-out, where your model offers it. Leica's stake-out: enter a set distance with the plus/minus keys; it beeps as you move slowly along the line approaching each multiple, starting within 0.1 m. Bosch's outdoor GLM 400 models also list it. Mark each point as the beep peaks.

Measuring outdoors in bright light

Use the point finder camera if your tool has one. Leica equips its outdoor DISTO models with a 4x zoom Pointfinder camera for when the laser cannot be located. Bosch's outdoor line: the Bosch BLAZE Outdoor GLM400C and GLM400CL use an adjustable zoom camera to find the laser target in bright conditions, up to 400 ft. Below about 10 m, trust the real dot over the camera image: Leica's FAQ material explains that parallax between laser window and camera optics moves the crosshair off the dot at short range.

Steady the tool. At long range, small hand movements swing the dot a long way. Leica's accuracy guidance for its point finder models: use a stable support or a tripod, and trigger by timer or touchscreen where offered, so the press does not move the tool.

Give the beam a target plate. Leica's DISTO X6 guidance: for measurements outdoors and in bright surroundings it is very helpful to use a target plate. A target plate increases range during daylight, or if the target has poor reflection properties (D2). Its message codes specify the face: white or grey when the signal is too strong, brown when there is too much background light.

Use shade and surface choice. At dusk, or if the target is in shadow, the range without a target plate increases (D2). Measure to a shaded face, pick a matt, light surface over a dark or glossy one, and shorten a failing long shot into two legs with addition.

Checking accuracy and calibration wording

Makers give a check, not user distance calibration, plus one user calibration on tilt-sensor models.

The Bosch accuracy check, in Bosch's order. Pick a stretch that never changes, about 3 to 10 m long, whose exact length you know. The best conditions are indoors, with a smooth target that reflects well. Measure that stretch ten times in a row. On the GLM 40, no single measurement should differ from the mean value by more than plus or minus 4 mm over the whole section in favourable conditions. Write the measurements down so you can compare later. Use the figure for your own model.

When to run the check. Bosch: carry out an accuracy check before continuing work after severe external influences, hard knocks or a fall.

The one calibration you can do yourself. On Leica tilt-sensor models, the user can recalibrate the sensor's zero level: Leica's guided procedure places the device on an absolutely flat surface, measures, turns it horizontally by 180 degrees, measures again, then repeats the pair with the lens facing up. That calibrates tilt, not distance. If a distance check fails repeatedly with a clean lens and a good target, neither maker offers a home adjustment: Leica directs you to your dealer, Bosch to its after-sales service through your dealer.

How to clean a laser measure

Clean when the lens or display needs it, and always before an accuracy check. Neither Leica nor Bosch sets a fixed interval: dirt is the trigger.

  1. Blow loose dust off the lens first, and do not touch the glass with your fingers (Leica, for its optics).
  2. Wipe the housing with a damp, soft cloth (Leica's care advice and Bosch's maintenance advice both say this).
  3. Wipe the reception lens and the laser outlet gently with a soft, lint-free cloth, taking the same care you would with glasses or a camera lens.
  4. Never put the device in water, and never use aggressive cleaning agents or solvents (both makers).

Laser measure maintenance checklist

TaskHow oftenSource
Wipe the lens, laser outlet and display with a soft clothWhen dirty, and before an accuracy checkLeica DISTO Care wording; Bosch maintenance wording
Run the distance accuracy checkAfter a hard knock, a fall or other severe external influence, before continuing workBosch operating instructions
Recalibrate the tilt sensor zero level (models with a tilt sensor)When tilt readings are in questionLeica DISTO tilt calibration procedure
Replace all batteries at the same time, same manufacturer and capacityAt each battery changeBosch battery wording
Remove the batteries before prolonged storageBefore any long period out of useBosch battery wording
Check the case, pouch and hand strap for wearWhen you pack the tool awayMaker supplied accessories, Leica and Bosch box contents

How to store a laser measure properly

Store the tool in its case or pouch, dry, away from damp, a hot vehicle in summer, and loose tools. Bosch's storage rule: batteries out for prolonged periods out of use, because they can corrode and self-discharge. Rechargeable models: follow the maker's charging wording (Klein's 93LDM200: its supplied USB-C cable). Keep the target plate in the case.

Troubleshooting: error codes and failed readings

ProblemLikely causeFix
Leica code 255Received signal too weak, measuring time too longChange target surface (e.g. white paper) or use a target plate (Leica)
Leica code 256Received signal too highChange target surface, or use the grey side of the target plate (Leica)
Leica code 257Faulty measurement, too much background lightUse the brown side of the target plate (Leica)
Leica code 258Outside the measuring rangeShorten the shot, or split it into two legs and add (Leica)
Leica code 220Hardware errorContact your dealer (Leica)
Bosch Error displayTarget reflects too intensely (a mirror) or too weakly (black fabric), or ambient light is too brightUse laser target plate or change target (Bosch)
Bosch Error display, after a temperature changeLaser outlet or reception lens misted upWipe the outlet and lens dry with a soft cloth (Bosch)
Bosch temperature warning flashingTool outside its operating temperature range (minus 10 to plus 45 degrees C, GLM 40)Wait until the tool reaches operating temperature (Bosch)
Display unchanged, tool reacts unexpectedlySoftware errorRemove batteries, restart after reinserting (Bosch)
Weak signal on a Klein modelReflected beam not reaching the tool; target too dark, rough or angledUse a smooth, medium-reflectivity target that reflects the beam directly back (Klein)
No reading completes, all indicators flashDefect detected by the tool's self-monitoringService route via your dealer (Bosch after-sales; Leica dealer)

Mistakes that damage a laser measure

  • Solvents and aggressive cleaners, above all on the lens: ruled out by both Leica and Bosch.
  • Immersing the tool, or cleaning it under a tap: both makers prohibit immersion outright. A splash rating is weather protection, not a cleaning method.
  • Dropping it and measuring on without a check: Bosch: hard knocks and falls trigger an accuracy check before further work.
  • Leaving batteries in for long storage: Bosch warns that batteries can corrode and self-discharge in prolonged storage.
  • Modifying the instrument: Klein: do not modify it in any way, as doing so could result in emission of hazardous laser radiation.

Safety tips when using a laser measure

These tools are Class 2 laser products in Leica's, Bosch's and Klein's own specifications.

  • Leica: do not stare into the laser beam, and do not point it at other people. Avoid aiming at reflective surfaces that could bounce the beam into eyes.
  • Bosch: do not point the laser beam at persons or animals, and do not stare into the beam yourself. Do not leave the tool unattended while it is switched on, and switch it off when you are not using it.
  • Klein: manual warning, in capitals: laser radiation, do not stare into beam, Class 2 laser. Never look directly into the beam; do not use optical equipment such as lenses or scopes to view it.
  • FDA: the regulator's laser hazard classes page places Class II (IEC Class 2) in the band where hazard increases when viewed directly for long periods, and if viewed with optical aids. Labelling for Classes II to IV must include a warning symbol with the class and output power.

When should you replace a laser measure

Replace when the failure is in the instrument, not the target, light or setting. The end-of-life signs the manuals support: the accuracy check fails repeatedly on a known distance with a clean lens and a good target; a hardware error code persists (Leica's 220); the lens or housing is damaged; the display is dead or, on Bosch tools, all indicators flash and corrective measures do not clear it. Both makers route such a tool to service first (Bosch: after-sales through your dealer; Leica: your dealer), so take a service verdict first. Weak battery, dirty lens, wrong reference setting and glossy target are not end-of-life signs.

The buying side: Best Laser Measure for Outdoor Use applies the outdoor tests (point finder, target plate, range in bright light) to the current picks, and How to Choose a Laser Measure walks the range, accuracy and mode decisions. Budget first: Best Laser Measure Under 100 answers that band on its own.

Laser Measure: Frequently Asked Questions

How often should you clean a laser measure?

When it needs it, not on a calendar: neither Leica nor Bosch sets a fixed interval. Clean the lens whenever filmed or dusty, and always before an accuracy check.

How can you make a laser measure last longer?

Lens clean and untouched by fingers, tool stored in its case, accuracy checked after hard knocks or falls, batteries replaced together and removed before long storage (Bosch).

How do you store a laser measure properly?

In its case or pouch, dry, away from damp and temperature extremes, batteries removed for prolonged periods out of use, because Bosch warns they can corrode and self-discharge.

What mistakes damage a laser measure most often?

Solvents on the lens, immersion, a drop without Bosch's post-drop accuracy check, batteries left in through long storage, and modifying the instrument (Klein).

When should you replace a laser measure instead of repairing it?

When the accuracy check keeps failing, a hardware error persists, or the lens, housing or display is damaged. A healthy laser beats a tape over long outdoor runs, where tape sags and needs a second person: Laser Measure vs Tape sets out where each tool wins.

Keep researching this laser measure

How we check care guides like these

Read the full Pick Hearth methodology
  • Every instruction, mode sequence and error correction traced to the manufacturer manual or official support page named in our research notes: reference settings, stake-out beeps and message codes come from the Leica, Bosch and Klein documents.
  • Where makers disagree we print each maker's figure rather than averaging: Bosch's plus or minus 4 mm check figure attached to the GLM 40 wording, and Leica's target plate faces as Leica specifies them.
  • No brand can pay for a place, and affiliate earnings never change the guidance: no product picks and no buy links, because no maker-branded part verified to our standard.

First published · Updated in place as manuals and guidance change